Cellular Telephone - Memory Upload Procedures
Group 84
Phone,
Navigation Systems
Bulletin Number
84 04 98
Woodcliff Lake, NJ
April 1998
Product Engineering
SUBJECT:
CMT 5000VR, CPT 6000VR Telephones, Memory Upload Procedures.
MODEL:
E39 5 Series, E38 7 Series vehicles equipped with CMT 5000VR or CPT 6000VR Cellular Telephones.
Situation:
After replacing a defective I-BUS Interface Box, a technician tests the phone and finds that the Phone Numbers, Name Tags, etc., previously stored
in the system, are only accessible via the Handset and are not available (depending on vehicle model and equipment level) through the MFL, MID or
Board Monitor.
Cause:
In order to have the information stored in the Transceiver (CMT 5000VR) or Portable Handset (CPT 6000VR) readily available to the integrated
vehicle system, a "Vehicle Copy" of this information must also be stored in the I-BUS Interface Box.
228
When an I-BUS Interface Box has been replaced, the information stored in the Transceiver or Portable Handset must be Uploaded (transferred) to
the Interface Box.
Warranty Information:
For information only.
Procedure
Use the following procedure to perform the Memory Upload:
^ CMT 5000VR (Mobil Phone) - Press: FNC MENU 90 STO
^ CPT 6000VR (Portable Phone) - Press: FNC 0 90 STO
In both cases, the Handset Display will remain blank for the duration of the Upload.
When the Up-load has been completed, the Handset Display will show DONE.
To confirm a successful Up-load, check that the identical information (Phone Numbers, Name Tags, etc.) is accessible and is in the same memory
locations, in the Handset, Instrument Cluster Display, MID or Board Monitor, depending on vehicle model and equipment level.
Important Note I:
On 528i and 528iA vehicles without Navigation System (Low Kombi), the telephone interface default mode has to be reprogrammed to "Low
Kombi" setting using the MID, in order to establish the communication link between MFL and MID.
The reprogramming procedure (which can also be found in the CMT 5000 or CPT 6000 Installation Instructions) should be performed in case of
an Interface Box replacement and prior to the Memory Upload.
Use following procedure to reprogram the Telephone Interface Default Mode:
1. Turn ignition Off for 5 seconds.
2. Turn ignition switch to Accessory position.
3. Press the TEL button on the MID (MID will go into phone mode).
4. Quickly press and hold the BMW soft key for approximately 9 seconds.
5. Display will cycle through BMW HELP and Roadside Assistance phone number, then will show Hardware and Software version (example:
EJB HW:01 SW:01). HIGH KOM, LOW KOM, and BMW will appear above the soft keys on the left side of the MID.
6. You will have 3 seconds to press the soft key below LOW KOM.
7. MID display will return to Dial Number mode.
To confirm that the default setting has been successfully changed: press the R/T button on the steering wheel. The MID display will then show
"MEMORY EMPTY!". If the procedure was unsuccessful, "DIAL NUMBER" will remain in the MID.
8. Turn ignition to Off position.
Important Note II:
On vehicles with BMW Navigation System the new Roadside Assistance phone number is "hard coded" in the I-BUS Interface through the
Board Monitor (procedure also to be found in the CMT 5000 or CPT 6000 Installation Instructions). If the I-Bus Interface Box in the vehicle is
ever replaced, the Roadside Assistance phone number programming procedure must be repeated.
Use following procedure to change the RSA phone number through the Board Monitor
1. Turn ignition to Accessory position.
2. Using the handset, enter: for CMT 5000VR- FCN, Menu, 95, CLR
for CPT 6000VR- FCN, 0, 95, CLR
3. Through the Board Monitor menu select Telephone mode.
4. Select Digit Entry mode.
5. Using the rotary dial, enter the RSA phone number:
for Mark I Navigation (up to 9/97)- 1-800-861-8360
for Mark II Navigation (from 9197)- 1-800-599-4809
229
6. Exit Digit Entry mode (by activating the arrow symbol on the rotary dial).
7. Select INFO mode (the phone number will remain in the display).
8. Using the handset, enter:
for CMT 5000VR- FCN, Menu, 95 (display must say Off), STO.
within 10 seconds FCN, Menu, 95, CLR.
for CPT 6000VR- FCN, 0, 95, STO.
within 10 seconds FCN, 0, 95, CLR.
If the reprogramming procedure was successful the Board Monitor will return to the screen with Digit Entry mode highlighted and the phone
number will disappear from the display. If the procedure was not successful it must be repeated.
9. Press MENU to return to the main menu.
