Identity Transfer Kits for CMT/CPT Phones
Group 04
Tools and Equipment
Bulletin Number
04 13 97
Woodcliff Lake, NJ
May 1998
Product Engineering
This Service Information bulletin supersedes S.I. 04 13 97 dated November 1997 which should be removed and discarded from your S.I. binder.
Changes to this revision are identified by a black bar.
SUBJECT:
Identity Transfer Kit for CMT 5000VR and CPT 6000VR Phones
MODEL:
E39, E38
220
Situation:
The new Identity Transfer kit (P/N 99 00 0 000 817) allows transferring the NAM (Number Assignment Module) programming and repertory
memory information (names and phone numbers) from a transceiver diagnosed as defective into a replacement transceiver for CMT 5000VR, CPT
6000VR phones.
Utilizing the equipment eliminates the need for the technician and/or customer to reprogram such information manually in the event of a transceiver
replacement.
Important:
Unfortunately, the ESN (Electronic Serial Number) of the transceiver cannot be transferred during the procedure, due to FCC regulations on
newer generation equipment. The local cellular carrier has to be contacted to transfer the new ESN number. Also, the customer has to reprogram
the voice tags into the memory of the phone.
Distribution of the following tools will be through the Automatic Tool Shipment Program. Additional tools may be purchased through your PDC.
Please refer to Pants Information bulletin I-24 dated 4/95 for tool warranty details. All prices in this bulletin are introductory prices. Introductory
prices are only valid during the Automatic Tool Shipment.
Repertory and NAM Transfer
The following setup and procedure is to be used to transfer repertory memory and NAM programming information from one BMW CMT5000VR
mobile transceiver to another.
Memory transfer setup for CMT 5000VR.
221
Detail of 8-pin adapter connection.
1. Remove the defective transceiver (84 11 1 470 099) and install the replacement transceiver (84 11 1 470 105).
2. Install the ID transfer cable (SLN7012B) between the vehicle harness and replacement transceiver.
3. Install the CMT5000VR 25-pin adapter (SYN6448A) between the other end of the ID transfer cable and the defective transceiver.
4. Install the 8 - pin adapter (SLN6749A) to the junction box (SLN7544B). Then plug in a handset into the 8 - pin adapter and install a data
cable (SKN4712A) between the 8 - pin adapter and the defective transceiver.
5. Install the other data cable (SKN4712A) between the junction box and the replacement transceiver. Turn the vehicle ignition on, turn the
switch on the junction box to the off position, plug in the junction box AC adapter and follow the transfer instructions.
Test Mode Command 800 # NAM Transfer
This command will transfer the contents of the Number Assignment Module from a defective telephone to a replacement telephone.
Test Mode Command 801 # Repertory Memory Transfer
This command will transfer names and numbers stored in memory from a defective telephone to a replacement telephone. However, voice tags
cannot be transferred and will have to be reprogrammed by the user.
Transfer Procedure
1. Connect the defective and replacement telephones as shown in the setup instructions.
2. Turn on the ignition, power on the defective telephone (numbers should appear in the display to indicate it is in test mode) and enter # 69 #.
3. Power on the replacement unit using the handset in the vehicle (numbers should appear in the display to indicate it is in test mode) and enter #.
4. Turn the switch on the junction box to position 1. Using the vehicle handset enter 800 # for NAM transfer, and wait for PASS to appear on the
display. Enter 801 # for repertory memory transfer and wait for PASS to appear.
5. Turn the switch on the junction box to the off position. Power off both telephones and the transfer process is complete.
Note:
If a FAIL code appears in the display during the transfer process, verify the setup and transfer procedures were followed correctly and reenter the
transfer command. If the transfer is still not successful the information will have to be entered into the replacement unit manually.
Repertory and NAM Transfer
The following setup and procedure is to be used to transfer repertory memory and NAM programming information from one BMW CMT5000VR
portable transceiver to another.
222
Transfer setup for CPT 6000VR.
Test Mode Command 800 # NAM Transfer
This command will transfer the contents of the Number Assignment Module from a defective telephone to a replacement telephone.
Test Mode Command 801 # Repertory Memory Transfer
This command will transfer names and numbers stored in memory from a defective telephone to a replacement telephone. However, voice tags
cannot be transferred and will have to be reprogrammed by the user.
Test Mode Command 802 # Preferred SIDs Transfer
This command will transfer the preferred SIDs that are programmed into the telephone (if any) from the defective telephone to the replacement
telephone.
Transfer Procedure
1. Connect the defective and replacement telephones as shown in the setup diagram with the switch on the junction box in the off position.
2. Power on the defective telephone and enter the following key sequence (FCN 00**83786633 STO, numbers should appear in the display to
indicate it is in test mode) and enter # 69 #.
3. Power on the replacement telephone and enter the following key sequence (FCN 00**83786633 STO, numbers should appear in the display to
indicate it is in test mode) and enter #.
4. Turn the switch on the junction box to position 1. Enter 800 # on the replacement telephone for NAM transfer, and wait for PASS to appear on
the display. Enter 801 # for repentory memory transfer and wait for PASS to appear. Then enter 802 # for Preferred SIDs transfer and wait for
PASS to appear on the display.
5. Turn the switch on the junction box to the off position. Power off both telephones and the transfer process is complete.
NOTE:
If a FAIL code appears in the display during the transfer process, verify the setup and transfer procedures were followed correctly and reenter the
transfer command. If the transfer is still not successful the information will have to be entered into the replacement unit manually.
